Before adding another blower to a common header, check whether the existing and proposed machines can operate together across the plant’s actual demand range. That means reviewing performance curves, branch pressure losses, controls, reverse-flow protection, and what happens during starts, stops, and trips—not just adding nameplate capacities.
Parallel blowers supply a shared pressure system. They don’t necessarily divide the load equally, and installing another machine doesn’t guarantee a proportional increase in process airflow. The header, downstream restrictions, and control sequence determine how much useful capacity the addition provides.
Start With the Process Requirement, Not the Available Blower
First, establish why another machine is being considered. More peak airflow, standby coverage, and better low-demand operation are different requirements. A blower selected for one may not satisfy the others.
Collect operating data through representative production or treatment cycles:
Flow: Minimum, normal, and peak requirements, including how quickly demand changes.
Pressure: Header pressure and pressure needed at the actual process users.
Operating combinations: Which blowers run together, at what speeds, and for how long.
Inlet conditions: Temperature, absolute pressure, filter restriction, and gas composition where applicable.
Process restrictions: Valve positions, diffuser condition, conveying-line conditions, or other downstream resistance.
Machine condition: Discharge temperature, motor load, vibration, and maintenance history.
Keep flow units consistent. Inlet actual cubic feet per minute and standard cubic feet per minute aren’t interchangeable. Standard flow also needs a defined reference temperature and pressure. Compare all machines on a common basis before combining capacities.
A header gauge alone won’t establish a capacity shortage. High pressure at the blower with poor flow at the process can point toward a restriction rather than insufficient equipment.
Build the Combined Performance Picture
For parallel operation, flows add at a shared header pressure; pressure capabilities do not add. Each blower must still develop enough discharge pressure to overcome both header pressure and its own branch losses.
The actual operating point comes from the combined blower performance and the system resistance. That resistance may include a relatively fixed requirement, such as wastewater submergence, plus losses that rise with flow through piping, valves, and diffusers.
Positive Displacement Blowers
A rotary lobe positive displacement blower moves approximately a fixed inlet volume per revolution. Delivered flow varies with speed, internal leakage, and operating conditions. Pressure comes from the resistance the machine works against.
Adding another unit generally adds flow, but the resulting higher system pressure can raise discharge temperature and required shaft power. Check every operating machine against its allowable differential pressure, temperature, speed, and motor loading—not just the new unit.
A positive displacement blower doesn’t have the same surge boundary as a centrifugal blower. It still requires appropriate pressure protection and must not be operated against a blocked discharge.
Centrifugal Blowers and Fans
Centrifugal machines have pressure-flow characteristics that strongly affect load sharing. At a given header pressure, each machine contributes the flow supported by its own curve, speed, inlet conditions, and branch losses.
If the common pressure pushes one blower below its stable operating range, it may surge or encounter another unstable condition, depending on the design. Fans can also have unstable regions that make parallel operation unsuitable without careful selection.
Review current manufacturer curves and operating limits for each planned combination. Two machines that work well separately may not work well together. Different technologies can sometimes share a header, but their load-sharing and protection requirements need an application-specific review.
Account for the Piping Between Each Blower and the Header
Common header pressure does not mean identical blower discharge pressure. One machine may discharge through a short branch; another may have a longer run, extra elbows, a restrictive silencer, or a check valve with substantial pressure loss.
Those differences affect delivered flow and loading. Compare pressures at consistent measurement locations, and include the losses between each blower and the header when evaluating performance.
Review the proposed connection for:
Branch and header sizes at the new total flow.
Losses through silencers, flexible connectors, check valves, and isolation valves.
Condensate drainage and potential liquid carryover into equipment.
Piping supports, thermal movement, and allowable nozzle loads.
Pressure pulsation, acoustic interaction, and vibration with multiple machines operating.
A larger connection alone may not resolve poor distribution farther downstream. If one process branch already takes more air than another, adding supply can preserve—or worsen—that imbalance.
Protect Running and Stopped Machines
A stopped blower connected to a live header needs protection against reverse flow. Otherwise, header air may pass backward through the machine, potentially causing reverse rotation or other damage.
Check valves must suit the flow range, pressure loss, temperature, installation orientation, and closing behavior. An oversized valve may chatter at low flow. A valve that closes poorly during a trip can allow a damaging transient.
Don’t treat a check valve as maintenance isolation. Follow facility isolation, lockout/tagout, and stored-energy procedures before work on equipment connected to a pressurized header.
For positive displacement equipment, review pressure-relief protection for each machine. An isolation or check valve must not leave a running blower separated from its required relief path. Relief sizing, location, settings, and discharge routing require qualified review against manufacturer instructions and applicable requirements. A pressure switch is not a substitute for required mechanical relief protection.
Make the Controls Work as One System
Independent controllers trying to maintain nearly identical pressure setpoints can fight each other. One blower speeds up while another slows down; a second machine starts, pressure rises, and the first unloads or stops.
A coordinated sequence should define:
Lead and trim duties: Which machine carries steady load and which adjusts to changing demand.
Staging: When another blower starts, when one stops, and what delays prevent repeated cycling.
Operating limits: Minimum and maximum speed, temperature, motor load, and stable flow where applicable.
Start permissives: Required valve positions and package conditions before starting into a pressurized system.
Failure response: Actions after a blower trip, sensor failure, communication loss, or power restoration.
Variable frequency drives can help match output to demand, but they don’t remove machine limits. Low-speed lubrication, motor cooling, prohibited speed bands, and centrifugal surge protection remain equipment-specific considerations.
The transition between machine combinations deserves particular attention. One blower may be near full capacity while two running together cannot turn down far enough. That gap can produce cycling or wasted discharge flow even though peak capacity looks adequate.
A Mid-South Aeration Example
Consider a hypothetical North Mississippi wastewater facility evaluating a third blower because basin airflow falls short during peak demand. The existing machines also run hotter than they did previously.
Before sizing the addition, compare blower discharge pressure, basin airflow, diffuser condition, inlet-filter restriction, and room temperature. Fouled diffusers or partly closed valves may have raised system resistance. Hot summer inlet air can also reduce mass flow at a given inlet volumetric flow and narrow available temperature margin.
The third machine may still be justified. But if the restriction remains, all operating units may face higher loading without delivering the expected process benefit. The review also needs to confirm that overnight low demand can be handled without unstable operation or excessive cycling.
What to Request Before Purchase and Commissioning
Give the supplier more than a horsepower target. Provide existing blower identification, curves, speed ranges, operating trends, a piping sketch, branch components, control descriptions, and the required duty with one machine unavailable.
Ask for a documented review of minimum, normal, and peak demand; proposed running combinations; hot-weather inlet conditions; and startup and trip behavior. Standby capacity only counts if the remaining machines can meet the required duty within their limits.
Commissioning should verify individual contributions, temperatures, motor loading, control stability, check-valve behavior, and process delivery. Qualified personnel should perform planned transition and protection testing under approved procedures. Don’t force unsafe conditions simply to demonstrate a protective function.
Bottom Line
Approve another blower only after the combined machines, piping, protection, and controls have been reviewed as a system. The useful result is a workable operating range—not just a higher total on the equipment schedule.
Process & Power can help facilities throughout Tennessee, Arkansas, and Mississippi review common-header blower applications and equipment selection. Bring the operating trends and piping information along with the proposed capacity.
Call Process & Power, Inc. at 901-362-5500 or visit us at 1721 Corporate Avenue, Memphis, TN 38132 for help with industrial air compressors, pumps, blowers, vacuum systems, and compressed air equipment and service throughout Memphis and the surrounding area.
